旱地生态学问题弱解对初值的连续依赖性

随着工业化的发展,人们越来越注重生态环境保护问题.利用能量方法,采用Sobolev不等式研究了旱地生态学问题,得到了旱地生态学问题非负弱解对初值的连续依赖性.     

Carrying Capacity of Stretching-bending Rectifier

In accordance with the deficient elongation of the Stretching-bending Rectifier, as well as the severe wear and slipping of V-belt , the driving system velocity ratio of rectifier and the calculation formula of the theoretical elongation are deduced, which are based on the analysis of its structure and reeling principle. The carrying capacity of the driving system is also analyzed and it reaches the main reason for the elongation of the stretching-bending rectifier that cannot reach request, which is caused by the step less torsion of fixed output of the continuously variable transmission. The improvement measure which can be achieved by increasing the stiffness of the spring to increase the output torsion of the continuously variable transmission is proposed. Thus it makes the actual coefficient of elongation,which can satisfiy the producing request.     

基于角位移控制的功率分流式自动变速器速比控制研究

阐述了功率分流式自动变速器中电机控制式无级变速单元的速比控制原理。通过对速比控制电机目标角位移、角位移滑模变结构控制器的建模,来确定整个控制器的设计参数。在对角位移目标轨迹跟踪的仿真中,控制器能够较好地实现在有外在负载干扰下对角位移目标轨迹的跟踪。     

无级变速拖拉机跃度最优化调速控制

针对无人驾驶拖拉机加减速导致的作业平稳性低和燃油经济性差等问题，该研究基于CVT（constantly variable transmission，无级变速传动）拖拉机，设计了一种基于贝尔曼最优性原理的最小跃度多项式局部速度规划算法。基于贝尔曼最优性原理和最优控制思想设计全局规划目标、局部规划目标及约束，提出基于最小跃度多项式的局部速度规划算法并开发速度跟随控制系统。田间试验表明，相对于无最优化调速技术的对照组，U型掉头的速度误差平均值和均方根分别降低42.31%和50.75%，加速度平均值与方差分别降低8.26%和16.36%，跃度平均值与方差分别降低7.65%和14.23%，发动机转速方差降低63.36%，发动机扭矩百分比方差降低60.26%，瞬时油耗方差降低71.25%，总油耗降低2.37%。直线行驶调速效果呈现相同趋势，与对照组相比，速度误差平均值和均方根分别降低9.45%和11.14%，加速度平均值与方差分别降低6.03%和13.68%。跃度平均值和均方根分别降低1.55%和3.59%。发动机转速方差降低31.78%，发动机扭矩百分比方差降低25.13%，瞬时油耗方差降低31.82%，总油耗降低2.48%。所提方法满足无级变速拖拉机无人驾驶速度平稳切换需要，并提高了燃油经济性。     

探索低成本连续生产中、高密度纤维薄板和异型板的方式

连续生产中、高密度薄板的方式是采用连续双钢带冷热压机,而国内人造板设备制造行业尚无制造连续双钢带冷热压机的能力。本文依据木纤维薄板矫直原理,提出采用简易连续热辊压压机加矫直机的方案,探索低成本连续生产中、高密度纤维薄板和异型板的方式,以解决实际生产问题。     

理论换段点下HMCVT换段离合器转矩交接及控制

针对液压机械无级变速器在换段过程中的动力中断和换段冲击问题,该研究以三段式液压机械无级变速器第二段切换第三段为例,通过建立动力学模型分析理论换段点下两段位的液压路功率方向变化规律,提出基于液压路功率方向的两阶段换段离合器转矩交接方法,并使用分段函数对两阶段离合器转矩交接轨迹进行优化,通过仿真对转矩交接方法正确性进行了验证。为了实现转矩的跟踪控制,基于终端滑模控制的方法设计了离合器控制器,通过对油压的跟踪控制实现转矩的跟踪控制,通过试验验证了控制器有效性。仿真和试验结果表明：在负载换段过程中,所提换段离合器转矩交接方法能够实现动力的平稳过渡,终端滑模控制器能够实现离合器油压的跟踪控制,从而实现转矩控制。在输入轴转速1 000 r/min,负载700 N·m工况下,使用终端滑模控制器控制两换段离合器进行换段,输出轴转速的波动范围为-20.6～7.4 r/min,输出轴转矩波动范围为-117.4～107.9 N·m,换段过程中最大冲击度为-6.16 m/s3,换段离合器的最大滑摩功为508.45 J,换段过程中无动力中断。该研究可为液压机械段变速器的换段控制提供参考。     

连作对棉田土壤枯、黄萎病菌数量及细菌群落的影响

采用选择培养法测定新疆库尔勒不同连作年限棉田土壤枯、黄萎病病菌数量的变化,运用PCR-DGGE(Polymerase chain reaction-denatured gradient gel electrophoresis)技术分析棉花连作对土壤细菌群落结构和多样性的影响。结果表明,不同连作年限棉田的枯萎病菌和黄萎病菌量具有相似的变化特征,即在5~20年连作年限内,土壤中病原菌量随着连作年限的延长而增加,20年连作土壤病原菌数量达到最高峰;连作超过20年,土壤菌源数量开始下降。不同连作年限棉田土壤中枯、黄萎病病原菌的数量与发病株率呈显著正相关关系。连作棉田土壤细菌群落的DGGE图谱分析显示,连作棉田土壤细菌种群的组成、结构、丰富度均发生变化。连作5~40年的棉田土壤细菌种群Shannon-Wiener多样性指数(H')、均匀度(EH′)和丰富度(S)指数均降低,且连作年限越长降低越突出。     

Researching and Developing a Hybrid Electrical Vehicle

There are more than two power source in Hybrid Electrical Vehicle(HEV). By using of assist accelerating, power regeneration, Idle stop and power management, HEV gains more acceleration performance and more fuel economy and better gas emission than Conventional Vehicle(CV). With Integrated Starter and Generator(ISG) as a auxiliary power source, batteries and battery control module and power manage module as a Load leveling Device (LLD), two prototype HEV separately equipped Manual Transmission (MT) and Continuously Variable Transmission (CVT) was successfully developed.     

Study on Simulation of Contact Friction Condition of Continously Variable Transmission

As metal Belt CVT(Continuously Variable Trans mission) acts as a kind of friction transmission, friction coefficient is a key parameter of CVT. The friction characters of CVTF(Continuously Variable Transmission Fluid) are mainly determined by fluid and contact state. The contact between belt and pulley can be regarded as a kind of contact between cylinder and cone. As their contact line is short, the curvature change of pulley along the contact line can be neglected. Then the contact problem of belt and pulley was reasonably simplified as a contact between cylinder and cylinder. Under the state of equivalent maximum stress, the contact friction condition of metal belt and pulley was simulated by the contact of ring and block in Timken Friction Test Machine.